/** * Marlin 3D Printer Firmware * Copyright (C) 2017 MarlinFirmware [https://github.com/MarlinFirmware/Marlin] * * Based on Sprinter and grbl. * Copyright (C) 2011 Camiel Gubbels / Erik van der Zalm * * This program is free software: you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation, either version 3 of the License, or * (at your option) any later version. * * This program is distributed in the hope that it will be useful, * but WITHOUT ANY WARRANTY; without even the implied warranty of * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the * GNU General Public License for more details. * * You should have received a copy of the GNU General Public License * along with this program. If not, see . * */ /** * Anet V1.0 board pin assignments */ /** * Rev B 16 JUN 2017 * * 1) no longer uses Sanguino files to define some of the pins * 2) added pointers to useable Arduino IDE extensions * */ /** * The standard Arduino IDE extension (board manager) for this board * is located at https://github.com/SkyNet3D/anet-board. * * Installation instructions are on that page. * * After copying the files to the appropriate location, restart Arduino and * you'll see "Anet V1.0" and "Anet V1.0 (Optiboot)" in the boards list. * * "Anet V1.0" uses the bootloader that was installed on the board when * it shipped from the factory. * * "Anet V1.0 (Optiboot)" frees up another 3K of FLASH. You'll need to burn * a new bootloader to the board to be able to automatically download a * compiled image. * */ /** * Another usable Arduino IDE extension (board manager) can be found at * https://github.com/Lauszus/Sanguino * * This extension has been tested on Arduino 1.6.12 & 1.8.0 * * Here's the JSON path: * https://raw.githubusercontent.com/Lauszus/Sanguino/master/package_lauszus_sanguino_index.json * * When installing select 1.0.2 * * Installation instructions can be found at https://learn.sparkfun.com/pages/CustomBoardsArduino * Just use the above JSON URL instead of Sparkfun's JSON. * * Once installed select the Sanguino board and then select the CPU. * */ /** * To burn a new bootloader: * * 1. Connect your programmer to the board. * 2. In the Arduino IDE select the board and then select the programmer. * 3. In the Arduino IDE click on "burn bootloader". Don't worry about the "verify failed at 1F000" error message. * 4. The programmer is no longer needed. Remove it. */ /** * Additional info: * * Anet Schematics - https://github.com/ralf-e/ANET-3D-Board-V1.0 * Wiring RRDFG Smart Controller - http://www.thingiverse.com/thing:2103748 * SkyNet3D Anet software development - https://github.com/SkyNet3D/Marlin/ * Anet Users / Skynet SW on Facebook - https://www.facebook.com/skynet3ddevelopment/ * * Many thanks to Hans Raaf (@oderwat) for developing the Anet-specific software and supporting the Anet community. */ #ifndef __AVR_ATmega1284P__ #error "Oops! Make sure you have 'Anet V1.0', 'Anet V1.0 (Optiboot)' or 'Sanguino' selected from the 'Tools -> Boards' menu." #endif #ifndef BOARD_NAME #define BOARD_NAME "Anet" #endif // // Limit Switches // #define X_STOP_PIN 18 #define Y_STOP_PIN 19 #define Z_STOP_PIN 20 // // Steppers // #define X_STEP_PIN 15 #define X_DIR_PIN 21 #define X_ENABLE_PIN 14 #define Y_STEP_PIN 22 #define Y_DIR_PIN 23 #define Y_ENABLE_PIN 14 #define Z_STEP_PIN 3 #define Z_DIR_PIN 2 #define Z_ENABLE_PIN 26 #define E0_STEP_PIN 1 #define E0_DIR_PIN 0 #define E0_ENABLE_PIN 14 // // Temperature Sensors // #define TEMP_0_PIN 7 // Analog Input (pin 33 extruder) #define TEMP_BED_PIN 6 // Analog Input (pin 34 bed) // // Heaters / Fans // #define HEATER_0_PIN 13 // (extruder) #define HEATER_BED_PIN 12 // (bed) #define FAN_PIN 4 // // Misc. Functions // #define SDSS 31 #define LED_PIN -1 /** * LCD / Controller * * Only the following displays are supported: * ZONESTAR_LCD * ANET_FULL_GRAPHICS_LCD * REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER */ #if ENABLED(ULTRA_LCD) && ENABLED(NEWPANEL) #define LCD_SDSS 28 #if ENABLED(ADC_KEYPAD) #define SERVO0_PIN 27 // free for BLTouch/3D-Touch #define LCD_PINS_RS 28 #define LCD_PINS_ENABLE 29 #define LCD_PINS_D4 10 #define LCD_PINS_D5 11 #define LCD_PINS_D6 16 #define LCD_PINS_D7 17 #define BTN_EN1 -1 #define BTN_EN2 -1 #define BTN_ENC -1 #define ADC_KEYPAD_PIN 1 #elif ENABLED(REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER) || ENABLED(ANET_FULL_GRAPHICS_LCD) // Pin definitions for the Anet A6 Full Graphics display and the RepRapDiscount Full Graphics // display using an adapter board // https://go.aisler.net/benlye/anet-lcd-adapter/pcb // See below for alternative pin definitions for use with https://www.thingiverse.com/thing:2103748 #define SERVO0_PIN 29 // free for BLTouch/3D-Touch #define BEEPER_PIN 17 #define LCD_PINS_RS 27 #define LCD_PINS_ENABLE 28 #define LCD_PINS_D4 30 #define BTN_EN1 11 #define BTN_EN2 10 #define BTN_ENC 16 #define ST7920_DELAY_1 DELAY_0_NOP #define ST7920_DELAY_2 DELAY_1_NOP #define ST7920_DELAY_3 DELAY_2_NOP #define STD_ENCODER_PULSES_PER_STEP 4 #define STD_ENCODER_STEPS_PER_MENU_ITEM 1 #endif #else #define SERVO0_PIN 27 #endif // ULTRA_LCD && NEWPANEL /** * ==================================================================== * =============== Alternative RepRapDiscount Wiring ================== * ==================================================================== * * An alternative wiring scheme for the RepRapDiscount Full Graphics Display is * published by oderwat on Thingiverse at https://www.thingiverse.com/thing:2103748. * * Using that adapter requires changing the pin definition as follows: * #define SERVO0_PIN 27 // free for BLTouch/3D-Touch * #define BEEPER_PIN 28 * #define LCD_PINS_RS 30 * #define LCD_PINS_ENABLE 29 * #define LCD_PINS_D4 17 * * The BLTouch pin becomes LCD:3 */ /** * ==================================================================== * ===================== LCD PINOUTS ================================== * ==================================================================== * * Anet V1.0 controller | ZONESTAR_LCD | ANET_FULL_ | RepRapDiscount Full | Thingiverse RepRap wiring * physical logical alt | | GRAPHICS_LCD | Graphics Display Wiring | http://www.thingiverse * pin pin functions | | | | .com/thing:2103748 *------------------------------------------------------------------------------------------------------------------------ * ANET-J3.1 8 *** | N/A | J3_TX *** | | * ANET-J3.2 9 *** | N/A | J3_RX *** | | * ANET-J3.3 6 MISO | N/A | MISO *** | EXP2.1 MISO | EXP2.1 MISO * ANET-J3.4 +5V | N/A | +5V | | * ANET-J3.5 7 SCK | N/A | SCK *** | EXP2.2 SCK | EXP2.2 SCK * ANET-J3.6 5 MOSI | N/A | MOSI *** | EXP2.6 MOSI | EXP2.6 MOSI * ANET-J3.7 !RESET | N/A | button | EXP2.8 panel button | EXP2.8 panel button * ANET-J3.8 GND | N/A | GND | EXP2.9 GND | EXP2.9 GND * ANET-J3.9 4 Don't use | N/A | N/C | | * ANET-J3.10 +3.3V | N/A | +3.3V *** | | * | | | | * | | | | * ANET-LCD.1 GND | GND | GND | EXP1.9 GND | EXP1.9 GND * ANET-LCD.2 +5V | +5V | +5V | EXP1.10 +5V | EXP1.10 +5V * ANET-LCD.3 27 A4 | N/C * | LCD_PINS_RS | EXP1.4 LCD_PINS_RS | EXP2.4 SDSS or N/C * * ANET-LCD.4 10 | LCD_PINS_D4 | BTN_EN2 | EXP2.3 BTN_EN2 | EXP2.3 BTN_EN2 * ANET-LCD.5 28 A3 | LCD_PINS_RS | LCD_PINS_ENABLE | EXP1.3 LCD_PINS_ENABLE | EXP1.1 BEEPER_PIN * ANET-LCD.6 11 | LCD_PINS_D5 | BTN_EN1 | EXP2.5 BTN_EN1 | EXP2.5 BTN_EN1 * ANET-LCD.7 29 A2 | LCD_PINS_ENABLE | N/C * | EXP2.4 SDSS or N/C * | EXP1.3 LCD_PINS_ENABLE * ANET-LCD.8 16 SCL | LCD_PINS_D6 | BTN_ENC | EXP1.2 BTN_ENC | EXP1.2 BTN_ENC * ANET-LCD.9 30 A1 | ADC_KEYPAD_PIN ** | LCD_PINS_D4 | EXP1.5 LCD_PINS_D4 | EXP1.4 LCD_PINS_RS * ANET-LCD.10 17 SDA | LCD_PINS_D7 | BEEPER_PIN | EXP1.1 BEEPER_PIN | EXP1.5 LCD_PINS_D4 * * N/C * - if not connected to the LCD can be used for BLTouch servo input * ** - analog pin -WITHOUT a pullup * *** - only connected to something if the Bluetooth module is populated */ /** * REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER * physical pin function * EXP1.1 BEEPER * EXP1.2 BTN_ENC * EXP1.3 LCD_PINS_ENABLE * EXP1.4 LCD_PINS_RS * EXP1.5 LCD_PINS_D4 * EXP1.6 LCD_PINS_D5 (not used) * EXP1.7 LCD_PINS_D6 (not used) * EXP1.8 LCD_PINS_D7 (not used) * EXP1.9 GND * EXP1.10 VCC * * * EXP2.1 MISO * EXP2.2 SCK * EXP2.3 BTN_EN2 * EXP2.4 SDSS * EXP2.5 BTN_EN1 * EXP2.6 MOSI * EXP2.7 SD_DETECT_PIN * EXP2.8 button * EXP2.9 GND * EXP2.10 NC */