Description	Qty	Lumber		Actual		Length
--------------------------------------------------------------------------------------------------------------------------------------
Legs		4	4x4		3.5x3.5		34.5 cut from 8 ft piece 1,2
Frame1		4	2x4		1.5x3.5		36.0 cut from 10 ft piece 1,2,3,4
Frame2		4	2x4		1.5x3.5		36.0 cut from 10 ft picee 1,2,3,4
Vertical Frame	4	2x4		1.5x2.0		32.5 cut from 10 ft piece 1,2,3,4
Crossbar1	1	2x4		1.5x3.5		37.5 cut from 8 ft piece 1
Crossbar2	1	2x4		1.5x3.5		37.5 cut from 8 ft piece 2
Crossbar3	1	2x4		1.5x2.5		37.5 cut from 8 ft piece 3
Crossbar4	1	2x4		1.5x2.5		37.5 cut from 8 ft piece 4
Electric Frame	4	2x4		1.5x3.5		17.0  cut from 8 ft piece 1,2,3,4
Trim		4	2x4		1.5x3.5		48.0  cut from 8 ft piece 5,6,7,8
Drawer Frame	8	2x2		1.5x1.5		17.0 cut from 8 ft piece 1,2
Top		1	3/4 MDF Sheet	46.0x46.0		
Surface		1	3/4 MDF Sheet	45.0x45.0
Doors		4	1/2 MDF  Sheet	16.5x19.0		
Drawer		4	1/2 MDF Sheet	7.0x16.5		
Bottom		1	1/2 MDF Sheet	37.5x37.5
Cabinet Side	2	1/2 MDF Sheet	26.125x34.0
Peg Board	4	Peg Board	16.0x22.375	
Door Peg Board	4	Peg Board	15.75x13.25


_have__	pine 4x4		8 ft	2 qty
_have__	pine 2x4		10ft	4 qty
_have__	pine 2x4		8ft	8 qty
_have__	pine 2x2		8 ft	2 qty
_have__	5/8 MDF		2 - 4x8 sheets (cut in half)
_have__	1/2 MDF		4 - 2x4 sheets
_have__	Peg Board	4 - 2x4 sheets
_have__	Hole plugs (flush)
_have__	Hole plugs (beaded)
_have__	Counter Sink	1	0.25 dia 
_have__	1/4 Wood Screws	24	1.00 in	for bottom
_have__	1/4 Wood Screws	24	1.25 in	for top
_have__	1/4 Wood Screws	32	1.25 in	for frame
_have__	1/4 Wood Screws	48	2.00 in	for frame
_have__	1/4 Wood Screws	8	2.00 in	for trim
_have__	Drawer Slides	4	16 in depth
_______	Drawer Handles	4	stainless
_______	Door Knob	4	stainless
_have__	Hinge		8	stainless -   1.5 x 2.0 post, door 1/2 overlap
_have__	Wood Glue	1
_have__	Dato Blade	1/8 to 1/2 (or wider)
_have__	Electric Plugs	8
_have__	Plug Covers	8


Assembly Order
_______	Assemble first side in the following order:
	a) Vertical frame (face down on ground)
	b) Lower frame (lay across vertical frame)
	c) Upper frame (lay across vertical frame)
	d) Drawer frame (insert into hole in vertical frame)
	e) Shelf frame (insert into hole in vertical frame)
	f) Electric panel (insert into hole in vertical frame)
	g) Peg board (slide into slots in vertical frame, lower frame, and electric panel)
	h) Leg on peg board side
	i) Leg on drawer side
_______	Build second side using same procedure as above (shares one leg with side one) 
_______	Build third side using same procedure as above (shares one leg with side one)
_______	Set upright on four legs.  (three sides completed)
_______	install lower cross member (notch up) between sides two and three
_______	install lower cross member (notch down) to side one.  (Notch meshes to other cross member)
_______	install bottom (groves up) (sits on cross members and notches cut in lower frame)
_______	install shelf
_______	install cabinet side to hold shelf
_______	install shelf on other side of cabinet side
_______	install cabinet side
_______	install two remaining shelf
_______	install last cabinet side by sliding between two shelves just installed
_______	install shelf keeper (slide down from top)
_______	remove two legs and build fourth side using same procedure as above
_______	install fourth side
_______	install electrical outlets
_______	install sub surface
_______	install t-track
_______	install trim
_______	drop in surface pieces
_______	install doors
_______	install drawers